Gene. HELP ME FIND MY MODEL NUMBER OWNER RICK'S APPLIANCE REPAIR APPLIANCE TECHNICIAN FOR 31 YEARS REFRIGERATION SPECIALIST ONLINE SERV TECH: ApplianceBlog.com CERTIFIED TYPE 1; TYPE 2.....REFRIGERATION SERVICE E.S. Gene. My range is a CEW30ef6gsc. navigate here
The disconnect plug is the most suspect component. In order to provide most accurate advice I need the complete model number of the oven and the part number of the EOC you installed. It is giving F11 error. Melde dich bei YouTube an, damit dein Feedback gezählt wird. weblink
Gene // Dec 18, 2014 at 7:58 pm Hello Jim, Sorry for the delay. The unit is only 2 years old Mar 08, 2013 | Electrolux EW30DF65GS Dual Fuel (Electric... When I used the oven the next day to heat taco shells, it got really hot (burnt them to chars!) and then the F10 code went off again- this time I
https://www.facebook.com/permalink.php?story_fbid...id... Can you please tell me, does this sound like a bad control board? Do you know who WCI is? #4 (permalink) 01-28-2008, 08:04 PM Gene Senior Expert APP Volunteer Join Date: Jul 2007 Location: Orange County, California Posts: 27,209 Hi Roger, Electrolux Oven Error Codes Gene.
Keep me posted. Electrolux Oven Error Code F23 Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen... thanks josh Gene // Apr 10, 2014 at 5:03 pm Hello Josh.
Measure the resistance of the sensor.
The normal reading should be about 1100 Ohms at the room temperature. F10 Error Code Kenmore Oven At the same time make sure the wire harness from the probe to the control panel is not damaged. You can try to use the old one but if you damage it, the part number for the overlay is 316419700 Good luck and keep us posted. Good luck.
Locate the two pins in the plug at the EOC that are connected to the sensor. http://www.fixya.com/tags/f10_error_code/browse/electrolux Carefully pull it out and, using an Ohmmeter, check the resistance between the sensor wires. Electrolux Oven F11 Error Code If the readings are the same and you continue to get the F10 error code when trying to cook, then the electronic control board will need to be replaced. Frigidaire Oven F10 Reset louis Posts 16 Replaced the oven sensor and I'm still getting the F10 error.
Does the door lock motor run or not? check over here Thank you. Order Appliance Parts with 365-Day Hassle Free Return Policy - AppliancePartsPros.com See inside of your appliance - diagrams and part photos for virtually every model. Thanks. F10 Error On Frigidaire Oven
Do you think it is the temp probe or EOC?? I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top. Thanks again! http://dssoundware.com/error-code/electrolux-oven-f11-error-code.php All rights reserved. © Applianceblog.com 2004 - 2014 Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen...
Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual . Frigidaire Oven F10 Beeping So the only solution is to replace the EOC. Gene.
There are two different potentiometers with the ESEC control system. I did notice the wiring diagram in the pouch on the back panel. The oven warmed up OK, and it seems to be working fine now. What Does F10 Mean On A Frigidaire Oven Gene // Apr 1, 2015 at 8:35 pm Hello Steve, Thank you for your question.
You may want to replace it as well. Gene // Feb 26, 2015 at 6:54 pm Hello Kimberly, Thank you for your question. ft. weblink The time now is 02:46 PM.
It gives me the F10 error sporadically. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? After much reserach I purchased a new EOC part # 316462861 which arrived today and I immediately installed it. The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician.
The question I have is : does the oven control sensor store these failures ? If the reading at the sensor is correct, the wiring between the sensor and the control is defective. It has to be exchanged under the part warranty. Slide-In Gas Range ...
Parts cat. Test continuity of lock motor windings. ft. Do you have a suggestion?
The correction for this problem is to replace the EOC. Oven Sensor Testing – Oven Troubleshooting & Repair - Dauer: 1:40 RepairClinic.com 269.881 Aufrufe 1:40 Kenmore & Whirlpool Range Repair - Oven Is Not Reaching Temperature - 79078859602 - Dauer: 6:29 When replacing a potentiometer, do not over-tighten the hex nut. Remove the back panel.
Sorry for the bad news but hope you understand... The things that could cause the over to overheat to the exterme of the F10 error code reqirements is during self clean normal cleaning temp. If this error code shown while the oven was in day time mode, the EOC would need to be replaced.